rcg e3 www.vishay.com vishay draloric revision: 01-sep-14 1 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 green thick film chip resistors features ? green resistor - does not use rohs exemptions ? stability ? r / r = 1 % for 1000 h at 70 c ? 2 mm pitch packaging option for 0603 size ? material categorization: ? for definitions of compliance please see www.vishay.com/doc?99912 notes ? these resistors do not feature a limited lifetime when operated within the permissible limits. however, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifeti me. ? marking: see datasheet sur face mount resistor markin g (document number 20020). ? power rating depends on the max. temperature at the solder po int, the component placement density and the substrate material. note (1) the power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow suppor t of the printed-circuit boar d (thermal resistance). the rated di ssipation applies only if the permitted film temp erature of 155 c is n ot exceeded. standard electrical specifications type case size imperial case size metric power rating p 70 w limiting element voltage u max. ac rms /dc v temperature coefficient ppm/k tolerance % resistance range ? series rcg0402 0402 rr1005m 0.063 50 100 0.5, 1 150 to 10m e24; e96 150 1.0 to 147 200 5 1.0 to 10m e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 1.5 a rcg0603 0603 rr1608m 0.1 75 100 0.5, 1 1.0 to 10m e24; e96 200 5 e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 2.0 a rcg0805 0805 rr2012m 0.125 150 100 0.5, 1 1.0 to 10m e24; e96 200 5 e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 2.5 a rcg1206 1206 rr3216m 0.25 200 100 0.5, 1 1.0 to 10m e24; e96 200 5 e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 3.5 a technical specifications parameter unit rcg0402 rcg0603 rcg0805 rcg1206 rated dissipation p 70 (1) w 0.063 0.1 0.125 0.25 operating voltage u max. ac rms /dc v 50 75 150 200 insulation voltage u ins (1 min) v 75 100 200 300 insulation resistance ? > 10 9 operating temperature range c - 55 to + 155 mass mg 0.65 2 5.5 10
rcg e3 www.vishay.com vishay draloric revision: 01-sep-14 2 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 part number and product description part number: rcg080510k0fkea type value tolerance tcr packaging rcg0402 rcg0603 rcg0805 rcg1206 r = decimal k = thousand m = million 0000 = 0 ? jumper d = 0.5 % f = 1.0 % j = 5.0 % z = jumper k = 100 ppm/k l = 150 ppm/k n = 200 ppm/k 0 = jumper ea, eb, ec, ed, ee, ei, el product description: rcg0805 100 10k 1 % ea rcg0805 100 10k 1 % ea type tcr resistance value tolerance packaging rcg0402 rcg0603 rcg0805 rcg1206 100 ppm/k 150 ppm/k 200 ppm/k 10r = 10 ? 10k = 10 k ? 1m = 1 m ? 0r0 = jumper 0.5 % 1 % 5 % ea, eb, ec, ed, ee, ei, el packaging type code quantity carrier tape width pitch reel diameter rcg0402 ed 10 000 paper tape acc. to iec 60286-3 type 1a 8 mm 2 mm 180 mm/7" ee 50 000 330 mm/13" rcg0603 ei 5000 paper tape acc. to iec 60268-3 type 1a 8 mm 2 mm 180 mm/7" ed 10 000 180 mm/7" el 20 000 285 mm/11.25" ee 50 000 330 mm/13" ea 5000 paper tape acc. to iec 60268-3 type 1a 8 mm 4 mm 180 mm/7" eb 10 000 285 mm/11.25" ec 20 000 330 mm/13" rcg0805 ea 5000 paper tape acc. to iec 60268-3 type 1a 8 mm 4 mm 180 mm/7" eb 10 000 285 mm/11.25" ec 20 000 330 mm/13" rcg1206 ea 5000 paper tape acc. to iec 60268-3 type 1a 8 mm 4 mm 180 mm/7" eb 10 000 285 mm/11.25" ec 20 000 330 mm/13" r c g 0 8 0 5 1 0 k 0 f k e a
rcg e3 www.vishay.com vishay draloric revision: 01-sep-14 3 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 functional performance notes ? no exemptions (e.g. pb in glass) may be applied to any substances or application for the green category ? all concentration levels are ba sed on homogenous materials dimensions in millimeters size dimensions solder pad dimensions reflow soldering wave soldering imperial metric l w h t1 t2 a b l a b l 0402 rr1005m 1.0 0.05 0.5 0.05 0.35 0.05 0.25 0.05 0.2 0.1 0.4 0.6 0.5 0603 rr1608m 1.55 + 0.10 - 0.05 0.85 0.1 0.45 0.05 0.3 0.2 0.3 0.2 0.5 0.9 1.0 0.9 0.9 1.0 0805 rr2012m 2.0 + 0.20 - 0.10 1.25 0.15 0.45 0.05 0.3 + 0.20 ? - 0.10 0.3 0.2 0.7 1.3 1.2 0.9 1.3 1.3 1206 rr3216m 3.2 + 0.10 - 0.20 1.6 0.15 0.55 0.05 0.45 0.2 0.4 0.2 0.9 1.7 2.0 1.1 1.7 2.3 green requirements substances concentration limit lead (pb) < 1000 ppm mercury (hg) < 1000 ppm cadmium (cd) < 100 ppm hexavalent chronium < 1000 ppm polybrominated biphenyl (pbb) < 1000 ppm polybrominated diphenyl ether (pbde) < 1000 ppm bromine (br) < 900 ppm chlorine (cl) < 900 ppm sum of bromine and chlorine ? 1500 ppm max. antimony (sb) < 900 ppm red phosphorous < 100 ppm derating ambient temperature in amb fraction of rated dissipation p 70 - 50 0 50 100 150 0 50 100 70 c %
rcg e3 www.vishay.com vishay draloric revision: 01-sep-14 4 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 test procedures and requirements en 60115-1 ? clause iec 60068-2 test method test procedure requirements permissible change ( ? r ) stability for product types: stability class 1 or better stability class 2 or better rcg e3 1 ?? to 10 m ? 1 ?? to 10 m ? 4.5 - resistance - 0.5 %, 1 % 5 % 4.7 - voltage proof u = 1.4 x u ins ; 60 s no flashover or breakdown 4.13 - short time overload u = 2.5 x ? 2 x u max.; duration acc. to style (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.17.2 58 (td) solderability solder bath method; sn96.5ag3cu0.5 non-activated flux; (245 5) c (3 0.3) s good tinning ( ? 95 % covered) no visible damage 4.8.4.2 - temperature coefficient (20/- 55/20) c and (20/125/20) c 100 ppm/k, 150 ppm/k 200 ppm/k 4.32 21 (uu 3 ) shear (adhesion) rr 1608 and smaller: 9 n rr 2012 and larger: 45 n no visible damage 4.33 21 (uu 1 ) substrate bending depth 2 mm; 3 times no visible da mage, no open circui t in bent position (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.23 - climatic sequence: - (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.23.2 2 (ba) dry heat 125 c; 16 h 4.23.3 30 (db) damp heat, cyclic 55 c; ? 90 % rh; 24 h; 1 cycle 4.23.4 1 (aa) cold - 55 c; 2 h 4.23.5 13 (m) low air pressure 1 kpa; (25 10) c; 1 h 4.23.6 30 (db) damp heat, cyclic 55 c; ? 90 % rh; 24 h; 5 cycles 4.23.7 - dc load u = 4.25.1 - endurance at 70 c u = ? u max.; 1.5 h on; 0.5 h off; 70 c; 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.18.2 58 (td) resistance to soldering heat solder bath method (260 5) c; (10 1) s (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.35 - flamability, needle flame test iec 60695-11-5; 10 s no burning after 30 s 4.24 78 (cab) damp heat, steady state (40 2) c; (93 3) % rh; 56 days (1 % r + 0.05 ? ) (1 % r + 0.1 ? ) 4.25.3 - endurance at upper category temperature 155 c, 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.40 - electrostatic discharge (human body model) iec 61340-3-1; 3 pos. + 3 neg. discharges; esd test voltage acc. to size (1 % r + 0.05 ? ) p 70 x r p 70 x r p 70 x r
rcg e3 www.vishay.com vishay draloric revision: 01-sep-14 5 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 all tests are carried out in accordance with the following specifications: ? en 60115-1, generic specification ? en 140400, sectional specification ? en 140401-802, detail specification ? iec 60068-2, environmental test procedures packaging of components is done in paper tapes according to iec 60286-3. 4.29 45 (xa) component solvent resistance isopropyl alcohol; 50 c; method 2 no visible damage 4.30 45 (xa) solvent resistance of marking isopropyl alcohol; 50 c; method 1, toothbrush marking legible, no visible damage 4.22 6 (fc) vibration, endurance by sweeping f = 10 hz to 2000 hz; x, y, z ? 1.5 mm; a ? 200 m/s 2 ; 10 sweeps per axis (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.37 - periodic electric overload u = ? 2 x u max.; 0.1 s on; 2.5 s off; 1000 cycles (1 % r + 0.05 ? ) 4.27 - single pulse high voltage overload, 10 s/700 s ? = 10 x ? 2 x u max.; 10 pulses (1 % r + 0.05 ? ) test procedures and requirements en 60115-1 ? clause iec 60068-2 test method test procedure requirements permissible change ( ? r ) stability for product types: stability class 1 or better stability class 2 or better rcg e3 1 ?? to 10 m ? 1 ?? to 10 m ? 15 x p 70 x r p 70 x r
legal disclaimer notice www.vishay.com vishay revision: 13-jun-16 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
